Φόρουμ
Latest images
Εγγραφή
ΣύνδεσηVector™ 2 Device Firmware
Σελίδα 1 από 1
Vector™ 2 Device Firmware
από Santosan Τετ 29 Ιουν 2016 - 10:36
[Πρέπει να είστε εγγεγραμμένοι και συνδεδεμένοι για να δείτε αυτή την εικόνα.]
[Πρέπει να είστε εγγεγραμμένοι και συνδεδεμένοι για να δείτε αυτόν το σύνδεσμο.]
as of June 22, 2016
Change History
Changes made from version 3.90 to 4.00:
Properly enable the status LED to prevent the unit from appearing non-functional when an incomplete mechanical connection between the pod and spindle occurs.
Changes made from version 3.81 to 3.90:
Correct accelerometer start-up error that was preventing meaningful data from being captured and reported
Fixed a condition where Vector could cause a display to divide by zero when receiving torque data
Install angle can be set in a pedal to pedal disconnected state.
Improved battery monitoring to make it less susceptible to sampling noise
Improved handling of parameter conflict between multiple displays
Prevent users from setting scale factor outside of the 0.75 to 1.25 range
Changes made from version 3.50 to 3.81:
Corrected two radio issues that were causing persistent loss of data reception either from the left side or from the entire system.
Improved pedal to pedal sync time.
Reduced opportunities for spontaneous un-pairing of pedals.
Corrected a math error that was causing periodic balance spikes.
Transmit time-averaged torque while coasting.
[Πρέπει να είστε εγγεγραμμένοι και συνδεδεμένοι για να δείτε αυτόν το σύνδεσμο.]
as of June 22, 2016
Change History
Changes made from version 3.90 to 4.00:
Properly enable the status LED to prevent the unit from appearing non-functional when an incomplete mechanical connection between the pod and spindle occurs.
Changes made from version 3.81 to 3.90:
Correct accelerometer start-up error that was preventing meaningful data from being captured and reported
Fixed a condition where Vector could cause a display to divide by zero when receiving torque data
Install angle can be set in a pedal to pedal disconnected state.
Improved battery monitoring to make it less susceptible to sampling noise
Improved handling of parameter conflict between multiple displays
Prevent users from setting scale factor outside of the 0.75 to 1.25 range
Changes made from version 3.50 to 3.81:
Corrected two radio issues that were causing persistent loss of data reception either from the left side or from the entire system.
Improved pedal to pedal sync time.
Reduced opportunities for spontaneous un-pairing of pedals.
Corrected a math error that was causing periodic balance spikes.
Transmit time-averaged torque while coasting.
Santosan- Administrator
-
Ηλικία : 54
Τόπος : Athens - West Side
Ημερομηνία εγγραφής : 06/10/2012
Αριθμός μηνυμάτων : 10879
Παρόμοια θέματα» Vector™ Device Firmware
» Vector S™ Device Firmware
» Vector 2S™ Device Firmware
» HRM-Run Device Firmware
» HRM-Run Device Firmware
» Vector S™ Device Firmware
» Vector 2S™ Device Firmware
» HRM-Run Device Firmware
» HRM-Run Device Firmware
Σελίδα 1 από 1
Δικαιώματα σας στην κατηγορία αυτή
Δεν μπορείτε να απαντήσετε στα Θέματα αυτής της Δ.Συζήτησης|
|
|